Knauf Home Energy Audit Nationwide

Knauf Home Energy Audit in Burbank: What to Know First

We provide independent Knauf home energy audit in Burbank, typically scheduled within 48 hours and completed in a single visit. Most audits run between $280 and $550 depending on home size and test scope, and you’ll get a written price before we start - no exceptions. This page is for Knauf owners in Burbank who want to know whether their insulation, air sealing, or duct system is performing to the R-value on the label or just resting on it. Call (213) 816-1699 for a free estimate, or text us if that’s easier.

Call (213) 816-1699

How Knauf Products Fail - and How We Fix Them

We’ve audited enough Burbank homes to know where Knauf products hide their problems. Here are the failure modes we see, the series they show up in, and what we do about them.

• Knauf EcoSeal Plus gaps at top plates in 1960s ranch homes. The water-based elastomeric sealant shrinks in Burbank’s dry summer heat, pulling away from drywall-to-top-plate joints in Magnolia Park and Rancho Equestrian neighborhoods. We remove the compromised bead, re-seal with Knauf EcoSeal Plus or transition to Knauf Insulation Seal when the substrate demands it, then verify with a blower-door test.
• Knauf Jet Stream Ultra settling in vented attics above 1,200 square feet. Blown-in fiberglass loses loft when attic temperatures exceed 140°F, which happens regularly in Burbank from July through September. The R-38 you paid for becomes R-28 or lower. We measure settled depth, calculate the true R-value, and recommend either re-blow to proper depth or conversion to Knauf Insulation EcoBatt in critical thermal zones.
• Knauf EcoBatt facing degradation in crawl spaces with seasonal moisture. The kraft facing delaminates when Burbank’s winter rains drive ground moisture through pier foundations, especially in the hillside areas near Verdugo Mountains. We inspect facing integrity, replace failed batts, and specify unfaced EcoBatt with a proper vapor barrier - never the other way around.
• Knauf Duct Wrap compression from improper hanger spacing. We find this in Burbank tract homes where original HVAC contractors spaced hangers at 4 feet instead of 18 inches. The R-6 wrap compresses to R-3 or less at the sag points. We document every hanger location, replace compressed sections, and re-space to Knauf’s published specification.
• Knauf Insulation Board gaps at rim joists in raised-floor construction. Thermal imaging reveals 1/4-inch gaps at butt joints that the original installer caulked with generic latex - wrong product, wrong joint. We remove, re-cut to tight tolerance, and seal with Knauf-approved foam sealant or transition to two-component spray foam when the geometry demands it.

Our Knauf Home Energy Audit Process

1. 1
   Schedule and scope. You call (213) 816-1699 or text us. We ask square footage, year built, and any known comfort issues. We give you a written price range before we book.
2. 2
   Arrival and walkthrough. Our technician arrives uniformed and background-checked, with a text sent when they’re en route under Haven Standard: Arrive on schedule. We walk the attic, crawl space, and duct runs with you, noting Knauf product lines and installation dates where visible.
3. 3
   Blower-door test. We depressurize the house to 50 Pascals - a standard pressure differential - and measure CFM50, the cubic feet per minute of air leakage. This single number tells us how much conditioned air your envelope is hemorrhaging.
4. 4
   Thermal imaging and duct blaster. FLIR camera work identifies thermal bypasses; duct blaster testing quantifies leakage in your Knauf-wrapped or Knauf-lined duct system. We photograph everything.
5. 5
   Written findings and next steps. You receive a documented photo record, blower-door number, duct leakage CFM, and a prioritized scope with flat pricing for any corrective work. No work starts without a written price and written warranty.
6. 6
   Cleanup and follow-up. We leave the site as we found it. If you proceed with corrections, we publish before-and-after blower-door numbers so you can verify the result.

Before

After

What Knauf Home Energy Audit Costs in Burbank

Homes in the Burbank Hills with finished attics or multiple crawl-space accesses trend toward the upper end. Post-war ranches in the flatlands near Victory Boulevard typically fall in the lower half. Every estimate includes our Free Second Opinion on any written competing quote - bring it in and we’ll read it with you.

Why Burbank Homeowners Call Topside Attic Insulation Burbank for Knauf Work

We’re an independent Knauf service provider - no manufacturer affiliation, which means we specify what works, not what we’re incented to move. Wes Okafor and our crew have been working Burbank attics long enough to know that a 1964 ranch in Magnolia Park has different thermal bypass patterns than a 1989 split-level near the studios. We also stock and service Reflectix radiant barrier products, so when a Knauf solution isn’t the right fit, we don’t pretend it is.

Every job carries the 365-Day Done Right Promise, documented in writing before anyone starts. Calls are answered by a live person, 24/7. We’ve sealed and insulated 9,000+ homes since 2016, and we publish before-and-after blower-door numbers on every applicable job because the R-value is what the label says. The performance is what the blower-door test says. We care about the second number.

FAQs