Owens Corning Home Energy Audit Nationwide

Owens Corning Home Energy Audit in Burbank: What to Know First

We provide independent Owens Corning home energy audit in Burbank, typically scheduling within 48 hours and completing the full diagnostic same day. Most audits run between $280 and $550 depending on home size and test scope, and we deliver a written price before any work starts - no exceptions. This page is for Owens Corning owners in Burbank who need a blower-door test, thermal imaging inspection, insulation inspection, or duct leakage test performed by technicians who understand how Owens Corning products age in this climate. Call (213) 816-1699 for a free estimate or to schedule.

Call (213) 816-1699

How Owens Corning Products Fail - and How We Fix Them

• Owens Corning AttiCat blown-in fiberglass settles unevenly in Burbank’s dry heat cycles. The Magnolia Park ranch homes we work were never designed for the 14-inch depth AttiCat needs to hit R-38. Over five to seven summers, vibration from the Bob Hope Airport flight path and thermal cycling create low spots near top plates where the fiberglass pulls away from the eaves. We remove the settled material, air-seal every top plate and penetration with acoustical sealant, then reinstall to a mapped depth grid - not a guess.
• Owens Corning Foamular XPS rigid board delaminates in vented crawl spaces with seasonal moisture. Burbank’s winter rains followed by dry Santa Ana conditions create expansion-contraction stress at the facer bonds. We find this most often in 1960s slab-on-grade homes near the Verdugo Mountains where perimeter drainage was never installed. Our fix: remove the failed board, seal the rim joist with closed-cell spray foam instead, and provide a vapor-barrier retrofit if groundwater is present.
• Owens Corning EcoTouch batts compress behind kneewalls in Burbank’s converted attics. Homeowners in the Rancho area finish these spaces without proper baffles, and the batts get walked on, stored against, or soaked from roof leaks that went undetected. Compressed fiberglass loses 30 to 50 percent of its labeled R-value. We pull the compromised batts, photograph the thermal bypasses, install proper vent chutes, and replace with new material cut to fit - not stuffed.
• Owens Corning QuietZone duct liner degrades in unconditioned Burbank attics where summer peak hits 140°F. The adhesive fails, the liner sags into the airstream, and the blower works harder to push the same CFM. We see this in homes with flex duct runs longer than 25 feet. Our repair: remove the failed liner, seal the duct seams with mastic, then reinsulate with wrapped fiberglass or replace the run entirely if the sag has created a permanent kink.
• Owens Corning Duration shingles with SureNail technology create thermal bridging when paired with inadequate attic ventilation. The strip shingle’s reinforced nailing zone is a hard point that conducts heat directly into the roof deck. In Burbank’s sun, this accelerates the degradation of whatever insulation sits below. We diagnose this with thermal imaging during our audit, then specify ridge vent additions or powered vent upgrades before touching the attic floor insulation - because new R-value over a 160°F deck is wasted money.

Our Owens Corning Home Energy Audit Process

1. 1
   Schedule and scope. Call (213) 816-1699. A live person answers. We confirm square footage, year built, and any known comfort complaints - hot rooms, high bills, dust from vents.
2. 2
   Arrival and walkthrough. Our technician arrives uniformed and background-checked. We inspect the attic hatch, crawl space access, and mechanical room. You get a text when we’re en route, under Haven Standard: Arrive on schedule.
3. 3
   Blower-door test. We install a calibrated fan in an exterior door and depressurize the house to 50 Pascals - the CFM50 reading tells us, in one number, how leaky the envelope is. Typical Burbank home from the 1960s reads 3,500 to 5,500 CFM50 before work.
4. 4
   Thermal imaging and duct pressure test. Flir camera scan of walls, ceilings, and duct runs. Duct blaster test if duct leakage is suspected. We mark every thermal bypass with painter’s tape for your reference.
5. 5
   Written report and price. Same day, you receive a Documented Photo Record, the blower-door number, thermal images, and a flat written price for any recommended work. No work starts without it - Haven Standard Clause 1.
6. 6
   Follow-up testing if work proceeds. On jobs where we seal and insulate, we run the blower door again and publish the before-and-after numbers. The R-value is what the label says. The performance is what the blower-door test says. We care about the second number.

Before

After

What Owens Corning Home Energy Audit Costs in Burbank

Most Owens Corning home energy audits in Burbank fall between $280 and $550. A 1,200-square-foot single-story with accessible attic and no duct testing lands near the low end. A 2,800-square-foot two-story with duct blaster, thermal imaging of all rooms, and crawl space inspection pushes the upper range. Homes with multiple HVAC zones or spray foam evaluation add $75 to $150 per additional test.

What moves the price: home size, number of attic accesses, whether the duct system is accessible, and if we need to depressurize a sealed crawl space. What doesn’t: the Owens Corning product line installed - our diagnostic protocol is the same whether you have AttiCat, EcoTouch, or Foamular.

We also provide a Free Second Opinion on any written estimate from another contractor. Bring us their scope; we’ll read it with you. Call (213) 816-1699 for an exact quote - estimates are free.

Why Burbank Homeowners Call Topside Attic Insulation Burbank for Owens Corning Work

We’ve been working Burbank attics, including the older ranch-style homes in Magnolia Park, long enough to know exactly where the thermal bypasses hide in a 1960s rafter bay. Wes Okafor built this crew on sequencing the job correctly: air-seal every penetration first, then blow in the cellulose or batts, so the R-value on the invoice actually matches the performance the homeowner measures on their utility bill.

Our 365-Day Done Right Promise covers all completed work. Every job closes with a Documented Photo Record and, where applicable, before-and-after blower-door readings. We’re independently owned and operated under The Haven Standard since 2016 - not a franchise, not a referral network. We also service Reflectix and other major brands, so if your audit reveals a multi-manufacturer situation, one crew handles it. Calls are answered by a live person, 24/7.

FAQs